News

Home / News / Industry News / 9-12 Series No.5A 7.5kW High-Pressure Centrifugal Fan

9-12 Series No.5A 7.5kW High-Pressure Centrifugal Fan

9-12 Series No.5A 7.5kW High-Pressure Centrifugal Fan

The 9-12 series is a high-pressure centrifugal fan range built for cupola furnaces, carton machinery, and other high-resistance air supply duty. This article focuses on the common No.5A size with a 7.5kW two-pole motor — structure, parameters, pros and cons, and selection guidance to help you judge whether it matches your system.

2900Speed (r/min, 2-pole)
2700–3400Airflow range (m³/h)
3100–2065Total pressure (Pa)
≤80℃Medium temperature limit
Overview

What the 9-12 high-pressure fan is

The 9-12 series high-pressure centrifugal fan is widely used for cupola furnace blast, carton machinery, and other duty that must overcome high system resistance. The "9-12" designation refers to a pressure coefficient of about 0.9 and a specific speed of about 12 — a low-specific-speed, high-pressure design with a narrower impeller of relatively large diameter, delivering high single-stage total pressure against long ducts, dense material beds, and similar resistance.


The 9-12 No.5A high-pressure centrifugal fan: one-piece scroll casing, axial inlet panel, direct-coupled impeller-motor drive, and anti-vibration base mounts. Size 5A corresponds to an impeller diameter of about 500 mm.
HP

Pressure-first aerodynamics

A low-specific-speed backward impeller on a 2900 r/min two-pole motor delivers roughly 2000–4800 Pa of total pressure in a single stage.

5A

Size 5A · 7.5kW build

Impeller diameter about 500 mm. The same size accepts a 5.5kW or 7.5kW motor; the 7.5kW build favors the higher-airflow section of the curve.

D

Direct-coupled drive

The impeller mounts straight on the motor shaft — no belt slip or tensioning maintenance, stable speed, compact layout, fewer service points.

Ref

Proven duty fit

Designed around cupola blast and carton-machine air duty, and also suited to high-pressure supply and pneumatic-conveying support.

Performance

9-12 series main technical parameters

Each size accepts motors of different power; the duty range shifts accordingly. The 5A + 7.5kW operating range is highlighted.

Size Power (kW) Speed (r/min) Airflow (m³/h) Total pressure (Pa)
5A 5.5 2900 1000–2680 4800–3239
5A 7.5 2900 2700–3400 3100–2065
6.3A 7.5 2900 1000–1875 8000–8300
6.3A 11 2930 1925–2750 8280–7850
6.3A 15 2930 2800–4000 7830–6100
6.8A 15 2930 1667–3600 9880–9420
6.8A 18.5 2930 3667–4567 9350–8400
6.8A 22 2930 4600–5500 8350–6760
7.1A 15 2930 1201–2978 10515–10821
7.1A 18.5 2930 3566–4148 10570–10103
7.1A 30 2950 4818–6344 9490–6933
7.7A 18.5 2930 1532–2983 12367–12953
7.7A 37 2950 3798–6697 12727–10520
7.7A 45 2970 7314–8092 9632–8154

Note: values are typical figures at standard conditions; the actual operating point moves along the fan performance curve as duct resistance changes. Selection should follow ZIFENG's tested performance curves and contract documents. Parameters for the same model may differ slightly across manufacturers.

Focus build: 5A + 7.5kWThis article

With a 7.5kW two-pole motor (2900 r/min), size 5A operates at 2700–3400 m³/h against 3100–2065 Pa. Compared with the 5.5kW build of the same size (1000–2680 m³/h at 4800–3239 Pa), the 7.5kW curve shifts to the right — more airflow at the same pressure — fitting systems with moderate resistance and a steady demand for higher volume.

The two curves meet near 2700 m³/h / 3100 Pa. If system resistance is high and required airflow stays below roughly 2680 m³/h, the 5.5kW build runs more economically; if the demand exceeds 2700 m³/h at relatively lower resistance, the 7.5kW build fits better. Check both against your measured system resistance curve.

Balanced view

Strengths and limits

Every model has its boundaries — here is the engineering view of the 9-12 5A.

ProsStrengths

  • High single-stage total pressure (up to about 4800 Pa at size 5A) without two-stage series connection
  • Backward impeller offers higher efficiency and lower energy use over long running hours
  • Non-overloading characteristic — the motor is less likely to overload when system resistance changes
  • Direct-coupled drive: no belt slip or tensioning, stable speed, fewer maintenance points
  • Compact footprint with anti-vibration base mounts for straightforward installation
  • Well-proven in cupola and carton-machinery duty, with long industry field record

Limits & cautionsBoundaries

  • Noise is relatively noticeable at 2900 r/min two-pole speed; silencers and acoustic measures are needed in noise-sensitive spots
  • Strict medium requirements: non-corrosive, non-flammable, non-viscous gas, temperature up to 80℃, dust and hard particles below 150 mg/m³
  • Airflow range centers on 2700–3400 m³/h; larger volumes should move up to size 6.3A and above
  • Fixed direct-drive speed; capacity control needs a VFD (check inverter compatibility at two-pole speed)
  • High-pressure duty demands tight impeller balancing and casing sealing — quality varies widely at low price points, so choose a dependable supplier
Applications

Where it fits

The pattern to look for: moderate airflow + high pressure + clean, ambient-temperature gas.

①

Cupola / melting furnace blast

Combustion air that must overcome the burden-bed resistance — the traditional core duty of the 9-12 series.

②

Carton machinery air duty

High-pressure air for suction, conveying, and dust extraction on carton production lines, with stable flow-pressure matching.

③

High-pressure supply / boosting

Boosting supply air through long ducts or high-resistance filters, or supplementing systems that fall short on pressure.

④

Pneumatic-conveying support

Support air for conveying light, clean, dry particles such as wood shavings — provided the medium limits are met.

Boundaries

Three duty types should look elsewhere: dusty or sticky media (choose an abrasion/dust-handling fan); medium above 80℃ (choose a high-temperature furnace fan); high airflow at low pressure (a medium-pressure series such as 4-72 runs more economically).

Decision guide

Five checks for the 5A 7.5kW build

Work through in order; if any step fails, consider an adjacent size or another series.

1

Verify the medium

Non-corrosive, non-flammable, non-viscous, temperature ≤80℃, dust ≤150 mg/m³ — all must hold before selecting this series.

2

Calculate system resistance

Total duct + equipment + bed resistance should fall near 2000–3100 Pa for the 5A 7.5kW to run near its efficient zone; above about 3200 Pa, look at the 5.5kW build or size 6.3A.

3

Match the airflow demand

Required volume between 2700–3400 m³/h fits directly; below 2680 m³/h consider the 5.5kW build, above 3400 m³/h move to 6.3A.

4

Allow margin

Keep roughly 10% margin on airflow and pressure, but avoid oversizing — high-pressure fans lose efficiency noticeably when running far from the design point.

5

Confirm installation and auxiliaries

Check foundation loading, vibration isolation, 380V supply, starting method (reduced-voltage or soft start recommended), and noise measures, then sign off the technical agreement.

Tip

Hand these four to an engineer — airflow, total pressure, medium temperature and dust content, and installation conditions; it beats judging by model name alone.

Why ZIFENG

Why source your high-pressure fan from ZIFENG

From duty-point calculation to complete delivery, with full-process support.

ZIFENG FANS supplies the full 9-12 series from size 5A to 7.7A, covering motor builds from 5.5–45kW, with material, drive, and control options customized to your medium and installation. Every unit is dynamically balanced and performance-tested before shipment, with the test report delivered alongside the fan.

  • Full 9-12 size range in supply, with 5A / 5.5kW and 5A / 7.5kW builds readily available
  • Duty points checked against measured system resistance to avoid oversizing waste
  • Impeller balancing + complete-unit performance testing, traceable quality
  • Optional VFD cabinets, silencers, and anti-vibration bases as one-stop auxiliaries

Selection is a service

5.5–45kW

Motor builds across the full 9-12 range from size 5A to 7.7A, matched to your duty.

Test report

Every unit ships with balancing and performance records, so rated values hold up on site.

Need a 9-12 5A 7.5kW high-pressure fan proposal?

Send us your airflow, total pressure, medium, and installation conditions — our engineering team will verify the duty point and recommend the configuration.



Submit feedback